当前位置： 易推广 > 厦门欣锐仪器仪表有限公司 > 产品展示 > RSA607A频谱分析仪
RSA607A频谱分析仪
价格：￥电议
品牌名称：$brandModel.Title(进口品牌)型号：RSA607A 原产地：中国大陆 发布时间：2021/10/28 19:19:30更新时间：2021/10/28 19:19:30
产品完善度： 访问次数：501
企业档案
会员类型：高级版会员
已获得易推广信誉 等级评定
(0 -40)基础信誉积累，可浏览访问
(41-90)良好信誉积累，可接洽商谈
(91+ )优质信誉积累，可持续信赖
易推广高级版会员：15年
工商认证 【已认证】
最后认证时间：
注册号： 【已认证】
法人代表： 【已认证】
企业类型：代理商 【已认证】
注册资金：人民币100万 【已认证】
产品数：49781
参观次数：5145171
手机网站：http://m.yituig.com/c11687/
商铺地址：http://www.fj17.com
详细内容
RSA607A频谱分析仪
- Frequency range
- RSA603A
- 9 kHz to 3 GHz
- RSA607A
- 9 kHz to 7.5 GHz
- Frequency marker readout accuracy
±（RE × MF + 0.001 × Span） Hz
RE: Reference Frequency Error
MF: Marker Frequency [Hz]
- Reference frequency accuracy
- Initial accuracy at Cal （30 min warm-up）
±1 x 10-6
- First year aging, typical
- ±1 x 10-6 （1 year）
- Cumulative error （Initial accuracy + temperature + aging）, typical
- 3 x 10-6 （1 year）
- Temperature drift
- ±0.9 x 10-6 （-10 to 60 °C）
- External reference input
- BNC connector, 50 Ω nominal
- External reference input frequency
Every 1 MHz from 1 to 20 MHz plus the following: 1.2288 MHz, 2.048 MHz, 2.4576 MHz, 4.8 MHz, 4.9152 MHz, 9.8304 MHz, 13 MHz, ａnd 19.6608 MHz.
The spurious level on the input signal must be less than -80 dBc within 100 kHz offset to avoid on-screen spurious.
- External reference input range
- ± 5 ppm
- External reference input level
- -10 to +10 dBm
RF input
- RF input
- RF Input Impedance
- 50 Ω
- RF VSWR （RF Attn = 20 dB）, typical
< 1.2 （10 MHz to 3 GHz）
< 1.5 （>3 GHz to 7.5 GHz）
- RF VSWR preamp ON, RSA603A ａnd RSA607A, typical
< 1.5 （10 MHz to 6 GHz, RF ATT=10 dB, preamp on）
< 1.7 （> 6 GHz to 7.5 GHz, RF ATT=10 dB, preamp on）
- Maximum RF input level
- Maximum DC voltage
- ±40 V （RF input）
- Maximum safe input power
+33 dBm （RF input, 10 MHz to 7.5 GHz, RF Attn ≥ 20 dB）
+13 dBm （RF input, 9 kHz to 10 MHz）
+20 dBm （RF input, RF Attn < 20 dB）
- Maximum safe input power （Preamp On）
+33 dBm （RF input, 10 MHz to 7.5 GHz, RF Attn ≥ 20 dB）
+13 dBm （RF input, 9 kHz to 10 MHz）
- Maximum measurable input power
+30 dBm （RF input, ≥10 MHz to Fmax, RF ATT Auto）
+20 dBm （RF input, <10 MHz, RF ATT Auto）
- Input RF attenuator
- 0 dB to 51 dB （1 dB step）
Amplitude ａnd RF
- Amplitude ａnd RF flatness
- Reference level setting range
- -170 dBm to +40 dBm, 0.1 dB step, （Standard RF input）
- Amplitude Accuracy at All Center Frequencies - Preamp ON （18 ℃ to 28 ℃ , 10 dB RF Attenuator）
- Preamp gain
27 dB at 2 GHz
21 dB at 6 GHz （RSA607A）
- Channel response （amplitude ａnd phase deviation）, typical
For these specifications, use a flat top window for maximum CW amplitude verification accuracy with the RF attenuator setting at 10 dB.
- Channel response （Amplitude flatness）
For these specifications, use a flat top window for maximum CW amplitude verification accuracy with the RF attenuator setting at 10 dB. The specifications are valid for the test center frequencies listed at the end of the table.
1Span extents cannot exceed lower frequency limit of the instrument
Trigger
- Trigger/Sync input, typical
Voltage range: TTL, 0.0 V to 5.0 V
Trigger level （Schmitt trigger）:
Positive-going threshold voltage: 1.6 V min, 2.1 V max
Negative-going threshold voltage: 1.0 V min., 1.35 V max
Impedance: 10 k ohms with schottky clamps to 0 V, +3.4 V
- External trigger timing uncertainty
>20 MHz to 40 MHz acquisition bandwidth: ±250 ns
Uncertainty increases as acquisition bandwidth is decreased.
- Power trigger
- Power trigger, typical
Range: 0 dB to -50 dB from reference level, for trigger levels > 30 dB above the noise floor.
Type: Rising or falling edge
Trigger re-arm time: ≤ 100 μsec
- Power trigger position timing uncertainty
>20 MHz to 40 MHz acquisition bandwidth: ±250 ns
Uncertainty increases as acquisition bandwidth is decreased.
- Power trigger level accuracy
±1.5 dB for CW signal at tuned center frequency for trigger levels > 30 dB above the noise floor.
This specification is in addition to the overall amplitude accuracy uncertainty for SA mode.
Noise ａnd distortion
All noise ａnd distortion measurements are made with the Preamp off, except where noted.
- 3rd Order IM intercept （TOI）
- +12 dBm at 2.130 GHz
- 3rd Order IM intercept （TOI）,
- Preamp off, typical
+10 dBm （9 kHz to 25 MHz）
+15 dBm （25 MHz to 3 GHz）
+15 dBm （3 GHz to 4 GHz, RSA607A ）
+10 dBm （4 GHz to 7.5 GHz, RSA607A）
- Preamp on, typical
-20 dBm （9 kHz to 25 MHz）
-15 dBm （25 MHz to 3 GHz）
-15 dBm （3 GHz to 4 GHz）
-20 dBm （4 GHz to 7.5 GHz, RSA607A）
- 3rd Order Inter-modulation distortion
-74 dBc at 2.130 GHz
Each signal level -25 dBm at the RF input. 2 MHz tone separation. Attenuator = 0, Reference level = -20 dBm.
- 3rd Order inter-modulation distortion
- Preamp off, typical
< -70 dBc （10 kHz to 25 MHz）
< -80 dBc （25 MHz to 3 GHz）
< -80 dBc （3 GHz to 4 GHz）
< -70 dBc （4 GHz to 6 GHz, RSA607A）
< -70 dBc （6 GHz to 7.5 GHz, RSA607A）
Each signal level -25 dBm at the RF input. 2 MHz tone separation. Attenuator = 0, Reference level = -20 dBm.
- Preamp on, typical
< -70 dBc （9 kHz to 25 MHz）
< -80 dBc （25 MHz to 3 GHz）
< -80 dBc （3 GHz to 4 GHz）
< -70 dBc （4 GHz to 6 GHz, RSA607A）
< -70 dBc （6 GHz to 7.5 GHz, RSA607A）
Each signal level -55 dBm at the RF input. 2 MHz tone separation. Attenuator = 0, Reference level = -50 dBm.
- 2nd Harmonic distortion, typical
- 2nd Harmonic distortion
< -75 dBc （40 MHz to 1.5 GHz）
< -75 dBc （1.5 GHz to 3.75 GHz, RSA607A）
- 2nd Harmonic distortion, Preamp on
< - 60 dBc , 40 MHz to 3.75 GHz, input frequency
- 2nd Harmonic distortion intercept （SHI）
+35 dBm, 40 MHz to 1.5 GHz, input frequency
+35 dBm, 1.5 GHz to 3.75 GHz, input frequency
- 2nd Harmonic distortion intercept （SHI）, Preamp on
+15 dBm, 40 MHz to 3.75 GHz, input frequency
- Displayed average noise level （DANL）
（Normalized to 1 Hz RBW, with log-average detector）
Phase noise
- Phase noise
- Integrated Phase （RMS）, typical
7.45 x 10-3radians @ 1 GHz
8.24 x 10-3radians @ 2 GHz
9.34 x 10-3radians @ 6 GHz
Integrated from 10 kHz to 10 MHz
Spurious response
- Residual spurious response （Reference = 30 dBm, RBW = 1 kHz）
<-75 dBm （500 kHz to 60 MHz）, typical
< -85 dBm （>60 MHz to 80 MHz）, typical
<-100 dBm （>80 MHz to 7.5 GHz）
- Spurious response with Signal （Image suppression）
< -65 dBc （10 kHz to < 3 GHz, Ref= -30 dBm, Atten = 10 dB, RF input Level = -30 dBm, RBW = 10 Hz）
< -65 dBc （3 GHz to 7.5 GHz, Ref= -30dBm, Atten = 10 dB, RF input Level = -30 dBm, RBW = 10 Hz）
- Spurious response with signal at CF
- Offset ≥ 1 MHz
- Spurious response with signal at CF
- 150 kHz ≤ offset <1 MHz, Span=1 MHz
1Power supply sidebands, 620-660 kHz: -67 dBc, typical
- Spurious response with signal at other than CF, typical
- Spurious response with signal at half-IF 1
- RSA603A, RSA607A
< -60 dBc, （CF: 30 MHz to 3 GHz, Ref = -30 dBm, Atten = 10 dB, RBW = 10 Hz, Span = 10 kHz）
Signal frequency = 2310 MHz, RF input level = -30 dBm
- RSA607A
<-60 dBc, （CF 3 G Hz to 7.5 GHz, Ref= -30 dBm, Atten = 10 dB, RBW=10 Hz, Span=10 kHz）
RF input Level = -30 dBm
1This is an input signal at half of the IF frequency.
- Local oscillator feed-through to input connector, typical
< -70 dBm, preamp off.
< -90 dBm, preamp on.
Attenuator = 10 dB.
Acquisition
- IF bandwidth
- 40 MHz.
- A/D converter
- 14 bits, 112 Ms/s.
- Real-Time IF Acquisition Data
- 112 Ms/s, 16-bit integer samples.
GPS location
- Format
- GPS/GLONASS/BeiDou
- GPS antenna power
- 3 V, 100 mA maximum
- Time to first fix, maximum
- Lock time ranges from 2 sec （hot） to 46 sec （cold start）.
- Horizontal position accuracy
GPS: 2.6 m
Glonass: 2.6 m
BeiDou: 10.2 m
GPS + Glonass: 2.6 m
GPS + BeiDou: 2.6 m
Test conditions: 24 hr. static, -130 dBm, full power
Tracking generator （Option 04）
- Tracking Generator （Option 04）
- Frequency range
10 MHz to 3 GHz （RSA603）
10 MHz to 7.5 GHz （RSA607）
- Sweep speed
6700 MHz/second, 101 points, 50 kHz RBW （11 mS per point）
Measured using a Panasonic Toughpad FZ-G1, Intel® Core? i5-5300U 2.3 GHz Processor, 8 GB RAM, 256 GB SSD, Windows®7 Pro.
- Frequency resolution
- 100 Hz
- TG output connector
- N type
- VSWR
- < 1.8:1, 10 MHz to 7.5 GHz, -20 dBm output level
- Maximum output power
- -3 dBm
- Output power level setting range
- 40 dB
- Output power level step size
- 1 dB
- Output power level step size accuracy
- ± 0.5 dB
- Output level accuracy
- ± 1.5 dB, 10 MHz to 7.5 GHz, -20 dBm output level
- Harmonics
- < -22 dBc
- Non-harmonic spurious
< -30 dBc; spurious < 2 GHz from TG output frequency
< -25 dBc; spurious ≥ 2 GHz from TG output frequency
- Reverse power without damage
- 40 Vdc, +20 dBm RF
- Transmission gain measurement error
Gain of +20 to -40 dB: ±1 dB
- Transmission gain measurement dynamic range
70 dB
SignalVu-PC standard measurements ａnd performance
- Measurements included
- SignalVu-PC/RSA607A key characteristics
- Maximum span
- 40 MHz real-time
9 kHz - 3 GHz swept
9 kHz - 7.5 GHz swept （RSA607A）
- Maximum acquisition time
- 1.0 s
- Minimum IQ resolution
- 17.9 ns （acquisition BW = 40 MHz）
- Tuning Tables
Tables that present frequency selection in the form of standards-based channels are available for the following.
Cellular standards families: AMPS, NADC, NMT-450, PDC, GSM, CDMA, CDMA-2000, 1xEV-DO WCDMA, TD-SCDMA, LTE, WiMax
Unlicensed short range: 802.11a/b/j/g/p/n/ac, Bluetooth
Cordless phone: DECT, PHS
Broadcast: AM, FM, ATSC, DVBT/H, NTSC
Mobile radio, pagers, other: GMRS/FRS, iDEN, FLEX, P25, PWT, SMR, WiMax
- DPX spectrum display
- Spectrum processing rate （RBW = auto, trace length 801）
≤10,000/s
- DPX bitmap resolution
- 201x801
- Marker information
- Amplitude, frequency, signal density
- Minimum signal duration for 100% probability of detection
- 100 μs
Span: 40 MHz, RBW = Auto, Max-hold on
Due to the non-deterministic execution time of programs running under the Microsoft Windows OS, this specification may not be met when the host PC is heavily loaded with other processing tasks
- Span range （continuous processing）
- 1 kHz to 40 MHz
- Span range （swept）
- Up to maximum frequency range of instrument
- Dwell time per step
- 50 ms to 100 s
- Trace processing
- Color-graded bitmap, +Peak, -Peak, average
- Trace length
- 801, 2401, 4001, 10401
- RBW range
- 1 kHz to 10 MHz
- DPX spectrogram display
- Trace detection
- +Peak, -Peak, Average（VRMS）
- Trace length, memory depth
- 801 （60,000 traces）
2401 （20,000 traces）
4001 （12,000 traces）
- Time resolution per line
- 50 ms to 6400 s, user selectable
- Spectrum display
- Traces
- Three traces + 1 math trace + 1 trace from spectrogram for spectrum display
- Trace functions
- Normal, Average （VRMS）, Max Hold, Min Hold, Average of Logs
- Detector
- Average （VRMS）, Average, CISPR peak, +Peak, -Peak, Sample
- Spectrum trace length
- 801, 2401, 4001, 8001,10401, 16001, 32001, ａnd 64001 points
- RBW range
- 10 Hz to 10 MHz
- Analog modulation analysis （standard）
- AM demodulation accuracy, typical
- ±2%
0 dBm input at center, carrier frequency 1 GHz, 1 kHz/5 kHz input/modulated frequency, 10% to 60% modulation depth
0 dBm input power level, reference level = 10 dBm, Atten=Auto
- FM demodulation accuracy, typical
±1% of span
0 dBm input at center, carrier frequency 1 GHz, 400 Hz/1 kHz input/modulated frequency
0 dBm input power level, reference level = 10 dBm, Atten=Auto
- PM demodulation accuracy, typical
±3% of measurement bandwidth
0 dBm input at center, carrier frequency 1 GHz, 1 kHz/5 kHz input/modulated frequency
0 dBm input power level, reference level = 10 dBm, Atten=Auto
- Signal Strength display
- Signal strength indicator
- Located at right side of display
- Measurement bandwidth
- Up to 40 MHz, dependent on span ａnd RBW setting
- Tone type
Variable frequency based on received signal strength
Sweep speed
- Full-span sweep speed
- Full span sweep speed, typical
5500 MHz/sec （RBW = 1 MHz）
5300 MHz/sec （RBW = 100 kHz）
3700 MHz/sec （RBW = 10 kHz）
950 MHz/sec （RBW = 1 kHz）
Measured using a Panasonic Toughpad FZ-G1, Intel® Core? i5-5300U 2.3 GHz Processor, 8 GB RAM, 256 GB SSD, Windows®7 Pro.
Spectrum display is only measurement on screen
- Tuning step time via API
- 1 ms
SignalVu-PC applications performance summary
- AM/FM/PM ａnd direct audio measurement （SVAxx-SVPC）
- Carrier frequency range （for modulation ａnd audio measurements）
- （1/2 × audio analysis bandwidth） to maximum input frequency
- Maximum audio frequency span
- 10 MHz
- FM measurements （Mod. index >0.1）
- Carrier Power, Carrier Frequency Error, Audio Frequency, Deviation （+Peak, -Peak, Peak-Peak/2, RMS）, SINAD, Modulation Distortion, S/N, Total Harmonic Distortion, Total Non-harmonic Distortion, Hum ａnd Noise
- AM measurements
- Carrier Power, Audio Frequency, Modulation Depth （+Peak, -Peak, Peak-Peak/2, RMS）, SINAD, Modulation Distortion, S/N, Total Harmonic Distortion, Total Non-harmonic Distortion, Hum ａnd Noise
- PM measurements
- Carrier Power, Carrier Frequency Error, Audio Frequency, Deviation （+Peak, -Peak, Peak-Peak/2, RMS）, SINAD, Modulation Distortion, S/N, Total Harmonic Distortion, Total Non-harmonic Distortion, Hum ａnd Noise
- Audio filters
Low pass, kHz: 0.3, 3, 15, 30, 80, 300, ａnd user-entered up to 0.9 × audio bandwidth
High pass, Hz: 20, 50, 300, 400, ａnd user-entered up to 0.9 × audio bandwidth
Standard: CCITT, C-Message
De-emphasis （μs）: 25, 50, 75, 750, ａnd user-entered
File: User-supplied .TXT or .CSV file of amplitude/frequency pairs. Maximum 1000 pairs
- APCO P25 Measurements （SV26xx-SVPC）
- Measurements
- RF output power, operating frequency accuracy, modulation emission spectrum, unwanted emissions spurious, adjacent channel power ratio, frequency deviation, modulation fidelity, frequency error, eye diagram, symbol table, symbol rate accuracy, transmitter power ａnd encoder attack time, transmitter throughput delay, frequency deviation vs. time, power vs. time, transient frequency behavior, HCPM transmitter logical channel peak adjacent channel power ratio, HCPM transmitter logical channel off slot power, HCPM transmitter logical channel power envelope, HCPM transmitter logical channel time alignment, cross-correlated markers
- Modulation fidelity, typical
CF = 460 MHz, 815 MHz
C4FM ≤ 1.0%
HCPM ≤ 0.5%
HDQPSK ≤ 0.25%
Input signal level is optimized for best modulation fidelity.
- Bluetooth Measurements （SV27xx-SVPC）
- Modulation formats
Basic Rate, Bluetooth Low Energy, Enhanced Data Rate - Revision 4.1.1
Packet types: DH1, DH3, DH5 （BR）, Reference （LE）
- Measurements
- Peak Power, Average Power, Adjacent Channel Power or InBand Emission mask, -20 dB Bandwidth, Frequency Error, Modulation Characteristics including ΔF1avg （11110000）, ΔF2avg （10101010）, ΔF2 > 115 kHz, ΔF2/ΔF1 ratio, frequency deviation vs. time with packet ａnd octet level measurement information, Carrier Frequency f0, Frequency Offset （Preamble ａnd Payload）, Max Frequency Offset, Frequency Drift f1-f0, Max Drift Rate fn-f0 and fn-fn-5, Center Frequency Offset Table ａnd Frequency Drift table, color-coded Symbol table, Packet header decoding information, eye diagram, constellation diagram
- Output power, In-band emissions ａnd ACP
- Level uncertainty: refer to instrument amplitude ａnd flatness specification
Measurement range: signal level > –70 dBm
- Modulation characteristics
Deviation range: ±280 kHz
Deviation uncertainty （at 0 dBm）
<2 kHz 1 + instrument frequency uncertainty （basic rate）
<3 kHz 1 + instrument frequency uncertainty （low energy）
Measurement range: Nominal channel frequency ±100 kHz
- Initial Carrier Frequency Tolerance （ICFT）
Measurement uncertainty （at 0 dBm）: <1 kHz + instrument frequency uncertainty
Measurement range: Nominal channel frequency ±100 kHz
- Carrier Frequency Drift
Measurement uncertainty: <1 kHz + instrument frequency uncertainty
Measurement range: Nominal channel frequency ±100 kHz
1 At nominal power level of 0 dBm
- General purpose digital modulation analysis （SVMxx-SVPC）
- Modulation formats
- BPSK, QPSK, 8PSK, 16QAM, 32QAM, 64QAM, 256QAM, PI/2DBPSK, DQPSK, PI/4DQPSK, D8PSK, D16PSK, SBPSK, OQPSK, SOQPSK, MSK, GFSK, CPM, 2FSK, 4FSK, 8FSK, 16FSK, C4FM
- Analysis period
- Up to 81,000 samples
- Measurement filter
- Root Raised Cosine, Raised Cosine, Gaussian, Rectangular, IS-95 TX_MEA, IS-95 Base TXEQ_MEA, None
- Reference Filter
- Gaussian, Raised Cosine, Rectangular, IS-95 REF, None
- Filter rolloff factor
- α：0.001 to 1, in 0.001 steps
- Measurements
- Constellation, Demod I&Q vs. Time, Error Vector Magnitude （EVM） vs. Time, Eye Diagram, Frequency Deviation vs. Time, Magnitude Error vs. Time, Phase Error vs. Time, Signal Quality, Symbol Table, Trellis Diagram
- Symbol rate range
- 1 k symbols/s to 40 M symbols/s
Modulated signal must be contained entirely within the acquisition bandwidth
- Adaptive equalizer
- Linear, Decision-Directed, Feed-Forward （FIR） equalizer with coefficient adaptation ａnd adjustable convergence rate. Supports modulation types BPSK, QPSK, OQPSK, π/2-DBPSK, π/4-DQPSK, 8-PSK, 8-DSPK, 16-DPSK, 16/32/64/128/256-QAM
- QPSK Residual EVM （center frequency = 2 GHz）, typical
0.6 % （100 kHz symbol rate）
0.8 % （1 MHz symbol rate）
0.8 % （10 MHz symbol rate）
0.8 % （30 MHz symbol rate）
400 symbols measurement length, 20 Averages, normalization reference = maximum symbol magnitude
- 256 QAM Residual EVM （center frequency = 2 GHz）, typical
0.6 % （10 MHz symbol rate）
0.7 % （30 MHz symbol rate）
400 symbols measurement length, 20 Averages, normalization reference = maximum symbol magnitude
- LTE Downlink RF measurements （SV28xx-SVPC）
- Standard Supported
3GPP TS 36.141 Version 12.5
- Frame Format supported
FDD ａnd TDD
- Measurements ａnd Displays Supported
- Adjacent Channel Leakage Ratio （ACLR）, Spectrum Emission Mask （SEM）, Channel Power, Occupied Bandwidth, Power vs. Time showing Transmitter OFF power for TDD signals ａnd LTE constellation diagram for Primary Synchronization Signal, Secondary Synchronization Signal with Cell ID, Group ID, Sector ID ａnd Frequency Error.
- ACLR with E-UTRA bands （typical, with noise correction）
1st Adjacent Channel 60 dB （RSA607A）
2nd Adjacent Channel 62 dB （RSA607A）
- Mapping （MAPxx-SVPC）
- Supported map types
- Pitney Bowes MapInfo （*.mif）, Bitmap （*.bmp）, Open Street Maps （.osm）
- Saved measurement results
- Measurement data files （exported results）
- Map file used for the measurements
- Google Earth KMZ file
- Recallable results files （trace ａnd setup files）
- MapInfo-compatible MIF/MID files
- Pulse measurements （SVPxx-SVPC）
- Measurements （nominal）
- Average On Power, Peak Power, Average Transmitted Power, Pulse Width, Rise Time, Fall Time, Repetition Interval（seconds）, Repetition Interval （Hz）, Duty Factor （%）, Duty Factor （ratio）, Ripple, Droop, Pulse-Pulse Frequency Difference, Pulse-Pulse Phase Difference, RMS Frequency Error, Max Frequency Error, RMS Phase Error, Max Phase Error, Frequency Deviation, Phase Deviation, Time Stamp, Delta Frequency, Impulse Response, Overshoot
- Minimum pulse width for detection
- 150 ns
- Average ON power at 18 °C to 28 °C, typical
±0.3 dB + absolute amplitude accuracy
For pulses of 300 ns width or greater, duty cycles of .5 to .001, ａnd S/N ratio ≥ 30 dB
- Duty factor, typical
- ±0.2% of reading
For pulses of 450 ns width or greater, duty cycles of .5 to .001, ａnd S/N ratio ≥ 30 dB
- Average transmitted power, typical
±0.5 dB + absolute amplitude accuracy
For pulses of 300 ns width or greater, duty cycles of .5 to .001, ａnd S/N ratio ≥ 30 dB
- Peak pulse power, typical
±1.2 dB + absolute amplitude accuracy
For pulses of 300 ns width or greater, duty cycles of .5 to .001, ａnd S/N ratio ≥ 30 dB
- Pulse width, typical
±0.25% of reading
For pulses of 450 ns width or greater, duty cycles of .5 to .001, ａnd S/N ratio ≥ 30 dB
- Playback of recorded signals （SV56xx-SVPC）
- Playback file type
R3F recorded by RSA600
R3F recorded by RSA306, RSA500, or RSA600
- Recorded file bandwidth
- 40 MHz
- File playback controls
- General: Play, stop, exit playback
Location: Begin/end points of playback settable from 0-100%
Skip: Defined skip size from 73 μs up to 99% of file size
Live rate: Plays back at 1:1 rate to recording time
Loop control: Play once, or loop continuously
- Memory requirement
- Recording of signals requires storage with write rates of 300 MB/sec. Playback of recorded files at live rates requires storage with read rates of 300 MB/sec.
- WLAN Measurements, 802.11a/b/g/j/p （SV23xx-SVPC）
- Measurements
- WLAN power vs. time; WLAN symbol table; WLAN constellation; spectrum emission mask; error vector magnitude （EVM） vs. symbol （or time）, vs subcarrier （or frequency）; mag error vs symbol （or time）, vs. subcarrier （or frequency）; phase error vs symbol （or time）, vs. subcarrier （or frequency）; channel frequency response vs. symbol （or time）, vs. subcarrier （or frequency）; spectral flatness vs. symbol （or time）, vs. subcarrier （or frequency）
- Residual EVM - 802.11a/g/j /p （OFDM）, 64-QAM, typical
2.4 GHz, 20 MHz BW: -39 dB
5.8 GHz, 20 MHz BW: -38 dB
Input signal level optimized for best EVM, average of 20 bursts, ≥16 symbols each
- Residual EVM - 802.11b, CCK-11, typical
2.4 GHz, 11 Mbps: 1.3 %
Input signal level optimized for best EVM, average of 1,000 chips, BT = .61
- WLAN Measurements 802.11n （SV24xx-SVPC）
- Measurements
- WLAN power vs. time; WLAN symbol table; WLAN constellation; spectrum emission mask; error vector magnitude （EVM） vs. symbol （or time）, vs subcarrier （or frequency）; mag error vs symbol （or time）, vs. subcarrier （or frequency）; phase error vs symbol （or time）, vs. subcarrier （or frequency）; channel frequency response vs. symbol （or time）, vs. subcarrier （or frequency）; spectral flatness vs. symbol （or time）, vs. subcarrier （or frequency）
- EVM performance - 802.11n, 64-QAM, typical
2.4 GHz, 40 MHz BW: -38 dB
5.8 GHz, 40 MHz BW: -38 dB
Input signal level optimized for best EVM, average of 20 bursts, ≥16 symbols each
- WLAN Measurements 802.11ac （SV25xx-SVPC）
- Measurements
- WLAN power vs. time; WLAN symbol table; WLAN constellation; spectrum emission mask; error vector magnitude （EVM） vs. symbol （or time）, vs subcarrier （or frequency）; mag error vs symbol （or time）, vs. subcarrier （or frequency）; phase error vs symbol （or time）, vs. subcarrier （or frequency）; channel frequency response vs. symbol （or time）, vs. subcarrier （or frequency）; spectral flatness vs. symbol （or time）, vs. subcarrier （or frequency）
- EVM performance - 802.11ac, 256-QAM, typical
5.8 GHz, 40 MHz BW : -38 dB
Input signal level optimized for best EVM, average of 20 bursts, ≥16 symbols each
28 Volt noise source drive
- 28 Volt noise source drive output
- Output Level
- 28 VDC @ 140 mA
- Output voltage turn ON/OFF time
Turn on: 100 ?S
Turn off: 500 ?S
Input ａnd output ports
- Inputs, outputs, ａnd inferfaces
- RF input
- N type, female
- External frequency reference input
- BNC, female
- Trigger/Sync input
- BNC, female
- Tracking Generator Source Output
- N type, female
- GPS Antenna
- SMA, female
- USB Device Port
- USB 3.0 – Type A
- USB Status LED
LED, dual color red/green
LED states:
Steady Red: USB power applied, or resetting
Steady Green: Initialized, ready for use
Blinking Green: Transferring data to host
Installation requirements
- Maximum power dissipation （fully loaded）
RSA600A: 45 W maximum.
- Surge current
2 A peak maximum, at 25 °C （77 °F） for ≤ 5 line cycles, after the product has been turned off for at least 30 seconds.
- Cooling clearance （applies to supported faces）
Bottom, top
0 mm （0 in.） with feet installed
6.3 mm （0.25 in.） without feet installed
Sides
0 mm （0 in.）
Rear: 38.1 mm （1.5 in.）
Physical characteristics
- Physical characteristics
- Width
- 222.3 mm （8.75 in）
- Height
- 75.0 mm （2.95 in）
- Length
- 358.6 mm （14.12 in）
- Net weight
- 2.79 kg （6.15 pounds）
Environmental ａnd safety
- Temperature
- Operating
- -10 °C to +55 °C （+14 °F to +131 °F）
- Non-operating
- -51 °C to +71 °C （-60 °F to +160 °F）
- Humidity
MIL-PRF-28800F Class 2
Operating:
5% to 95±5%RH （relative humidity） in the temperature range of +10 °C to 30 °C （+50 °F to 86 °F）
5% to 75±5% RH above +30 °C to 40 °C （+86 °F to 104 °F）
5% to 45±5% RH above +40 °C up to +55 °C （+86 °F to +131 °F）
<10 °C （+50 °F） humidity is uncontrolled; non-condensing
- Altitude
- Operating
Up to 3000 m （9,842 ft.）
- Non-operating
Up to 12000 m （39,370 ft.）
Dynamics
- Vibration
- Operating
Tektronix Class 3 Random Vibration Test at 0.31 GRMS: 5-500 Hz, 3 Axes at 10 min/axis
- Non-Operating
MIL-PRF-28800F Class 3
2.06 GRMS, 5 500 Hz, 10 minutes per axis, 3 axes （30 minutes total）
- Shock
- Operating
- Test method per Military Standard MIL-PRF-28800F 1-4
- Non-Operating
- Exceeds the requirements of Military Standard MIL-PRF-28800F
- Handling ａnd transit
- Bench handling, operating
MIL-PRF-28800F Class 3
- Transit drop, non-operating
- MIL-PRF-28800F Class 2
热门标签：RSA607A频谱分析仪
