NAWT高电压试验核相器验电器

产品简介

NAWT高压核相器验电器，应用于电力线路、变电所的相位校验和相序校验，具有核相、测相序、验电等功能具备很强的抗干扰性，符合（ EMC ）标准要求，适应各种电磁场干扰场合。将被测高电压相位信号由采集器取出，经过处理后直接发射出去。由核相仪接收并进行相位比较，对核相后的结果定性。因NAWT无线高压核相仪是无线传输，真正达到安全可靠、快速准确，适应各种核相场合。

产品别名

核相仪，核相装置，无线核相器，高压核相器，高压核相仪，语音核相器，语音核相仪，无线核相仪

产品特性

1、屏幕显示内容：无线高压核相仪，不同相、同相、频率、X、Y、 、 、。

2、电源：主机采用可充电电源，X 和 Y 采集器 采用5 节 AG10 电池。

3、自动关机：开机后8分钟左右主机会自动关机 。

4、接触被测强电场时，仪器会自动报警。

产品参数

①准确度：同相误差≤15°，不同相误差≤15°

②采样速率 3 次 / 秒

③X和Y采集器电源电压为7.5V ±1.5V

④X和Y采集器工作电流≤5mA

⑤主机和 X、Y采集器的视距传输距离为X、Y≥20m

⑥工作环境：0℃┉ +50℃ 湿度：≤85%RH

⑦储存环境：0℃┉ +55℃ 湿度：≤85%RH

⑧本产品所测电压等级为 0.38KV┉220KV

安全事项

1、现场测试时，操作人员应按电力部门高压测试安全距离标准进行操作。

2、所测试绝缘杆电压等级为 ≤ 220KV 。

3、（特别注意：每次使用前请认真检查绝缘杆的绝缘性能，注意天气情况，严格遵守国家高压试验的相关规定！）

4、使用时应认真执行本单位安全规章制度，并严格遵守DL408-91安全工作规程（发电厂变电所电气部份）相关规定，仔细保管仪器，定期检查绝缘。

5、绝缘杆为6节伸缩式，在使用时，不管工作电压是否为最高电压，均要把伸缩绝缘杆拉到最长状态（约3.2米），握手时只能握在第六节上，不得在第五节上握手。

NAWT Wireless High-voltage Phasing Tester

Product introduction

NAWT Wireless High-voltage Phasing Tester , used in power lines , substations ａnd phase sequence phase check verification , with nuclear phase , phase sequence , electrical inspection ａnd other functions with a strong anti-interference, compliance (EMC ) standards, adapt to various electromagnetic interference occasions . High voltage phase signal will be measured by the collector out emitted directly after the treatment . Received by the nuclear phase ａnd the phase comparison , the results for the nuclear phase characterization. Because NAWT Wireless high-pressure nuclear phase meter is a wireless transmission , thereby achieving safe, reliable, fast ａnd accurate , adapt to various nuclear phase occasion.

Also called name

Nuclear phase meter , nuclear phase devices, wireless nuclear phase device, high-voltage nuclear phase device, high-voltage nuclear phase meter , voice nuclear phase device, wireless nuclear phase device

The Characteristics of the products

1.NAWT Wireless High-voltage Phasing Tester adopting large-capacity ａnd maintenance-free battery, which completely solve the disposable electricity shortage ａnd troublesome replacement for carbon battery, button batteries ａnd other disposable battery, especially suitable for field work ; without loading the battery, so it do not cause spark , therefore the device complies with safety  mining equipment safety designing.

2.In the long-distance testing, the visible range will up to 200m, ａnd can be used through the walls.

3.The phase, waveform, ａnd frequency date will be showed on the LCD screen, the testing is quite safe,fast ａnd reliable, with real female voice broadcasting.

4.Adopting the telescopic insulating rod , is portable ａnd easy to use, the insulation performance meet requirements of electric insulation withstand testing.

5.The portable receiver with elegant design ａnd non-slip treatment process

6.The total device adopts advanced technology, small ａnd light.

The parameters of the products

① Accuracy: phase error ≤ 15 °, different phase error ≤ 15 °

② Sampling rate 3 times / sec

③ X ａnd Y collector supply voltage is 7.5V ± 1.5V

④ X ａnd Y collector current ≤ 5mA

⑤ host ａnd X, Y acquisition the sight transmission distance of X, Y ≥ 20m

⑥ working environment : 0 ° ┉ +50 ° humidity : ≤ 85% RH

⑦ storage environment : 0 ° ┉ +55 ° humidity : ≤ 85% RH

⑧ the product of the measured voltage level of 0.38 KV ┉ 220KV

Power supply: AC110V/115V/120V/127V/220V/230V/240V, can optional

Input frequency: 50Hz/60Hz optional

Note: Our users can ｓelect the corresponding power which based on their local supply voltage ａnd frequency, ａnd we will confirm it before the delivery (or inform us that the goods will be used in which country advance)

Safety issues:

1.While testing on-site, the operator shall stay in a safe distance to operate.

2.The tested insulating rod voltage rating is ≤ 220KV.

3.( Special attention: Please checking the insulation rod carefully before using, pay attention to the weather, please strict compliance with the relevant national high-voltage testing regulation! )

4.Should earnestly implement the safety rules ａnd regulations, ａnd strictly comply with the relevant provisions of DL408-91 safety regulations (Electrical Power Substation part), keeping the instruments carefully ａnd checking the insulation regularly.

5.The insulation rod is 6 telescopic rod , when in use, regardless of the operating voltage is the highest voltage , are put telescopic insulating rod pulled up state ( about 3.1 meters ) , griping the Section VI, can＇t on Section V.